Commercial · Orlando, FL
Protect storefronts, equipment, and pedestrian areas with professional concrete bollard installation from Orlando Concreters, serving Orlando since 2015. We set new steel pipe, removable, and sleeve-set bollards in properly sized concrete footings for long-term impact resistance and code-ready layouts.
A durable bollard starts below grade. We begin with site verification and utility locates, then lay out spacing to match your doors, drive lanes, and protected assets. Our crew excavates or cores to the specified diameter and depth, installs form tubes when needed, and places compacted base material for stable bearing. Bollards are plumbed and braced, then we place reinforced concrete (typically 3,000-4,000 psi) with rebar cages or dowels as required, consolidating the pour to reduce voids and improve bond around the post or sleeve.
Central Florida conditions call for drainage-aware details and clean, durable finishes. We set the top elevation to shed water, avoid ponding at the slab edge, and protect nearby asphalt with proper isolation and patch transitions. After placement we finish the collar or cap for the intended use, including broom-finish, light trowel, or flush-to-slab where a trip-free surface is needed. For high-visibility areas, we can install post covers and apply yellow safety coatings or reflective bands after cure, with attention to surface prep so paint adheres and resists peeling.
Orlando customers choose us for straightforward scope, consistent field execution, and respect for active job sites. We bring the right equipment for the condition, including core rigs for existing concrete, skid-steer excavation when access allows, and mixing and placement methods sized for small or large runs. Our crews work to plan, keep bollards plumb and aligned, and coordinate around storefront traffic, loading schedules, and other trades. Orlando Concreters is licensed and insured, and we provide clear written estimates so you can approve quantities, spacing, and finish details with confidence.
Before we leave, we walk the installation with you and confirm alignment, clearances, and the finished surface around each footing. You get a clean job site, proper backfill and patching, and a cure plan appropriate for the schedule, including guidance on when the area can reopen to foot traffic and vehicles. We also document the bollard type used (embedded, sleeve-set, or removable), approximate footing size, and any coordination notes for striping, signage, or wheel stops. If you need additional protection later, the layout is easy to extend with matching spacing and finishes.
Yes. We provide a free written estimate after reviewing site access, square footage, grade, and the scope of demolition, forming, reinforcement, and finish.
Yes. We handle saw-cutting where needed, demolition, loading, and disposal, then rebuild the base and forms for the new pour.
When permits are required, we can coordinate the process and build to Florida Building Code requirements. We will tell you up front if permitting is likely for your scope.
Yes. We install stamped concrete with texture mats, border patterns, and color options, then apply a suitable sealer based on the finish and expected wear.
Common causes include poor subgrade compaction, inadequate base, improper drainage, lack of control joints, and heavy loads on thin sections. Some cracking is normal, but good design and prep reduce random cracking and settlement.
Concrete bollard installation is one of the simplest ways to reduce vehicle impact risk at storefronts, loading areas, sidewalks, and equipment pads. The performance comes down to layout, footing size, reinforcement, and careful placement so each bollard stays plumb and transfers loads into competent soil, not just a thin slab. Orlando Concreters installs fixed and removable bollards for commercial properties, multifamily sites, and homeowner drive approaches, with clear spacing and finish options that fit the use case.
Our process starts with a quick field review, utility coordination, and a layout you can approve. For new placements we excavate to the required diameter and depth, set the post or sleeve, brace it, then place concrete with appropriate reinforcement. For existing concrete, we can core-drill through slabs and install new footings without unnecessary demo, then patch and finish around the collar for a clean, trip-resistant transition.
We install common bollard types such as steel pipe bollards (often 4-6 inch schedule pipe), sleeve-set removable posts, and impact-protection placements around doors, meters, dumpster enclosures, and pedestrian paths. Finish and visibility details matter, so we can coordinate post covers, safety yellow coatings, and reflective elements after cure, and we pay attention to drainage so water does not pond around the base.
If you are planning a new site, retrofitting protection after a near miss, or replacing damaged posts, we can provide a written estimate with quantities, spacing, and installation method. Ask about combining bollards with related concrete work like curb repairs, small slab replacements, and wheel stop pads to keep the project efficient and consistent.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in Orlando. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.
