Commercial · Orlando, FL
Concrete curb and gutter controls stormwater, protects pavement edges, and keeps parking lots and drive aisles from unraveling. Orlando Concreters has served Orlando since 2015, building and replacing curbs, gutters, and curb returns for homes, HOAs, and commercial sites with clean lines and proper drainage.
Good curb and gutter starts below grade. We sawcut and remove failed concrete, then excavate to a consistent subgrade and proof-roll to find soft spots. Base is rebuilt with compacted #57 stone or graded road base in lifts, then set to line and grade with stringline, laser level, and stakes so water runs to the intended inlets and swales. We install forms for straight runs, curb returns, and valley gutter where needed, and place expansion joints at tie-ins and fixed structures to control movement.
Central Florida rain loads and sandy soils make drainage and edge support non-negotiable. We set positive slope to avoid birdbaths, protect low points, and match existing asphalt or concrete elevations so water does not undermine the pavement. For placement we use ready-mix concrete (typically 3,500-4,000 psi) and consolidate with internal vibration where appropriate, then finish to the right texture, usually broom-finish on exposed faces and a clean trowel where specified. If vehicles will cross, we can thicken sections, add dowels or rebar reinforcement, and build ADA-aligned curb ramps and detectable warning areas when the site requires it.
Orlando customers choose us because we treat curb and gutter like a drainage system, not just a border. Our crews verify grades before the pour, communicate tie-in heights with other trades, and keep access and safety in mind around storefronts, loading areas, and residential driveways. You get a clear written scope, jointing plan, and mix/finish selection that fits the use case, from light residential curb to heavy-use commercial curb returns. We are licensed and insured, and we focus on durable work that reduces callbacks from cracking, settlement, and washout.
Before we leave, we walk the line with you, confirm water flow, and check transitions at drive approaches, curb returns, and existing pavement edges. We handle cleanup, haul-off, and curing protection, then provide guidance on sawcut control joints (if applicable), sealant options, and realistic reopen times based on thickness and traffic. You receive a free written estimate, a schedule you can plan around, and curb and gutter built to the site grades, with tight forms, consistent reveal, and clean edges that make the whole property look finished.
Yes. We provide a free written estimate after reviewing site access, square footage, grade, and the scope of demolition, forming, reinforcement, and finish.
Yes. We handle saw-cutting where needed, demolition, loading, and disposal, then rebuild the base and forms for the new pour.
When permits are required, we can coordinate the process and build to Florida Building Code requirements. We will tell you up front if permitting is likely for your scope.
Yes. We install stamped concrete with texture mats, border patterns, and color options, then apply a suitable sealer based on the finish and expected wear.
Common causes include poor subgrade compaction, inadequate base, improper drainage, lack of control joints, and heavy loads on thin sections. Some cracking is normal, but good design and prep reduce random cracking and settlement.
A properly built concrete curb and gutter does three jobs at once, it channels stormwater, protects pavement edges, and creates clean boundaries for parking and landscaping. Orlando Concreters installs new curb and gutter and replaces failing sections where cracking, settlement, and erosion are already causing drainage problems. Whether you need a short residential run or long commercial frontage, we focus on line, grade, and compaction so the concrete performs through heavy rain and daily traffic.
Concrete curb and gutter is often where drainage issues show first. If water is ponding along the edge of a drive aisle or washing out soil behind the curb, the fix is usually a combination of correct slope, stable base, and sound joints. We remove the failed concrete by sawcutting for clean edges, rebuild the subgrade, and set forms to the proper reveal and flow line. Control joints and expansion joints are placed at logical intervals and at tie-ins to help manage shrinkage and movement.
For commercial properties, we pay special attention to curb returns, curb ramps, and areas that see turning loads from trucks and service vehicles. When the application calls for it, we thicken the section, add reinforcement, and coordinate elevations with asphalt overlays, sidewalks, and drainage structures. Finish matters too, a consistent broom-finish and crisp edging improves traction and keeps the site looking uniform long after the pour.
If you are planning new construction, repairs, or a drainage correction, we can help you choose the right curb and gutter profile and layout for your site. Request a free written estimate and we will review existing grades, drainage paths, and tie-in points, then provide a straightforward plan for a curb and gutter system that holds up in Orlando’s weather.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in Orlando. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.
